SINGAPORE-BASED · DELIVERED WORLDWIDEsales@gearboxbuddy.com
Home / Blog / News / Why Gearboxes Leak Oil — and What to Check First
GearboxBuddy · Blog / News

Why Gearboxes Leak Oil — and What to Check First

GearboxBuddy article · October 28, 2026

Blog · Maintenance & Repair · October 28, 2026
Blue industrial gearbox showing input and output shaft sealing locations
An oil-lubricated gearbox has several potential leakage paths. Illustration supplied from Sealing Notes.

A gearbox oil leak does not always mean the oil seal is defective. Replacing the seal may stop the leak temporarily, but the problem can return if oil level, housing pressure, shaft condition or the sealing arrangement remains unsuitable.

The most useful approach is to look at the complete sealing system. For maintenance teams, four checks matter most: oil supply and return, gearbox ventilation, external contamination and shaft speed.

1. Check where the oil actually comes from

Start by cleaning the accessible area and finding the first fresh oil trace. Oil can run down from a cover, housing joint or fitting and collect near a shaft. The lowest drip point may be some distance from the source.

Record when the leak occurs: during startup, after the gearbox warms up, continuously under load, or after shutdown. Also note recent changes, such as an oil change, seal replacement or a different mounting position. These observations help narrow the investigation before parts are removed.

2. Check oil level, oil return and the breather

Verify the oil level using the procedure for the actual gearbox and mounting orientation. Do not add extra oil as a precaution. Excess oil and foaming can increase the amount of lubricant reaching the shaft exit.

The input and output shafts may experience immersion, splash oil or oil mist. Having enough oil in the housing does not automatically mean the sealing lip receives the right amount locally.

Oil must also be able to drain away from the sealing chamber. The small-scale return action at a lip contact cannot replace the chamber's main return passages. Where drawings show baffles or drain paths, check that they are clear and correctly assembled.

Inspect the specified breather as well. Restricted ventilation can create a pressure difference across the seal and affect its contact conditions. Follow the OEM procedure when inspecting the lubrication system, with the drive isolated and hot oil allowed to cool.

3. Choose a sealing arrangement for the environment

A standard radial lip seal, a Taconite-type combination and a non-contact labyrinth serve different requirements. They are not simply basic, better and best versions of the same product.

Radial lip seals use contact between the sealing lip and shaft. Their performance depends on suitable lubrication, a sound running surface and a material compatible with the actual oil and temperature.

Taconite-type arrangements add external protection for demanding contamination conditions. Depending on the design, an oil-retaining element works with a grease-filled labyrinth or other exclusion features. The grease maintenance is part of the sealing system, so confirm the specified grease, access and regreasing interval.

Cutaway of a sealing assembly with a grease fitting
Example of a regreasable sealing assembly. Component details and maintenance requirements vary by design. Source: Sealing Notes.

Non-contact oil labyrinths avoid a rubbing working lip at the oil-sealing interface. However, their suitability still depends on oil management, installation orientation and protection against external contamination. Ask how the arrangement retains oil during shutdown as well as during operation.

Before changing the sealing principle, check the complete assembly with the gearbox OEM or seal supplier. Matching the outside dimensions alone does not establish that a replacement will work.

Cutaway showing an alternative gearbox shaft-sealing arrangement
An alternative shaft-sealing construction. Check the exact drawing rather than identifying a seal solely from its appearance. Source: Sealing Notes.

4. Consider shaft speed and condition

Seal contact speed depends on shaft diameter as well as rpm. At the same rpm, a larger shaft has a higher surface speed. Check the selected seal's suitability for the combined speed, lubricant, temperature and pressure conditions.

Remaining below a catalogue speed limit does not guarantee a particular service life. The source article's speed chart suggests that leakage deserves closer attention in some higher-speed groups, but it does not provide a universal safe-speed limit or a numerical leakage probability.

If a leak returns after replacement, inspect the shaft track for wear, corrosion or scratches. Check relevant shaft movement and bearing condition against the equipment requirements. A new seal cannot correct an unsuitable running surface or a mechanical support problem.

English input-shaft speed distribution and qualitative relative leakage-frequency chart
Input-shaft peripheral speed and relative leakage frequency. English redraw of the supplied chart: the three highest speed bands are combined in the distribution; leakage bar heights are approximate because the original has no numerical y-axis scale.

A short checklist before replacing the seal

  • Locate the first fresh oil trace and record when it appears.
  • Confirm oil level, mounting orientation and lubricant specification.
  • Inspect the breather and any documented oil-return paths.
  • Check the shaft track, relevant shaft movement and installation condition.
  • Confirm seal design, dimensions and lubricant compatibility.
  • Verify the repair through startup, warm operation, shutdown and restart.

The aim is to address the reason for leakage, so the next seal has a suitable environment in which to operate.

Need help identifying a gearbox seal?

Send GearboxBuddy the gearbox nameplate, shaft location, seal markings, dimensions and clear photographs. Include the oil specification and a brief description of when the leak occurs.

Request a quotation

For new maintenance articles, subscribe to the GearboxBuddy RSS feed.

Sources: Adapted and expanded from Sealing Notes' article on oil-lubricated gearbox sealing, using the illustrations supplied by the reader. Technical background: Flender shaft-sealing guidance and SEW-EURODRIVE troubleshooting guidance. Follow the instructions for the installed gearbox and selected seal.

All articles

Let’s review your requirement.

Send the nameplate, drawing or part reference, quantity and delivery destination.

Send an enquiry